Waite
William F.
Waite
William F.
No Thumbnail Available
Search Results
Now showing
1 - 4 of 4
-
ArticleHydro-bio-geomechanical properties of hydrate-bearing sediments from Nankai Trough(Elsevier, 2015-03-01) Santamarina, J. Carlos ; Dai, Sheng ; Terzariol, Marco ; Jang, J. ; Waite, William F. ; Winters, William J. ; Nagao, Jiro ; Yoneda, Jun ; Konno, Yoshihiro ; Fujii, Tetsuya ; Suzuki, K.Natural hydrate-bearing sediments from the Nankai Trough, offshore Japan, were studied using the Pressure Core Characterization Tools (PCCTs) to obtain geomechanical, hydrological, electrical, and biological properties under in situ pressure, temperature, and restored effective stress conditions. Measurement results, combined with index-property data and analytical physics-based models, provide unique insight into hydrate-bearing sediments in situ. Tested cores contain some silty-sands, but are predominantly sandy- and clayey-silts. Hydrate saturations Sh range from 0.15 to 0.74, with significant concentrations in the silty-sands. Wave velocity and flexible-wall permeameter measurements on never-depressurized pressure-core sediments suggest hydrates in the coarser-grained zones, the silty-sands where Sh exceeds 0.4, contribute to soil-skeletal stability and are load-bearing. In the sandy- and clayey-silts, where Sh < 0.4, the state of effective stress and stress history are significant factors determining sediment stiffness. Controlled depressurization tests show that hydrate dissociation occurs too quickly to maintain thermodynamic equilibrium, and pressure–temperature conditions track the hydrate stability boundary in pure-water, rather than that in seawater, in spite of both the in situ pore water and the water used to maintain specimen pore pressure prior to dissociation being saline. Hydrate dissociation accompanied with fines migration caused up to 2.4% vertical strain contraction. The first-ever direct shear measurements on never-depressurized pressure-core specimens show hydrate-bearing sediments have higher sediment strength and peak friction angle than post-dissociation sediments, but the residual friction angle remains the same in both cases. Permeability measurements made before and after hydrate dissociation demonstrate that water permeability increases after dissociation, but the gain is limited by the transition from hydrate saturation before dissociation to gas saturation after dissociation. In a proof-of-concept study, sediment microbial communities were successfully extracted and stored under high-pressure, anoxic conditions. Depressurized samples of these extractions were incubated in air, where microbes exhibited temperature-dependent growth rates.
-
ArticleSimultaneous determination of thermal conductivity, thermal diffusivity and specific heat in sI methane hydrate(Blackwell Publishing, 2007-03-11) Waite, William F. ; Stern, Laura A. ; Kirby, S. H. ; Winters, William J. ; Mason, D. H.Thermal conductivity, thermal diffusivity and specific heat of sI methane hydrate were measured as functions of temperature and pressure using a needle probe technique. The temperature dependence was measured between −20°C and 17°C at 31.5 MPa. The pressure dependence was measured between 31.5 and 102 MPa at 14.4°C. Only weak temperature and pressure dependencies were observed. Methane hydrate thermal conductivity differs from that of water by less than 10 per cent, too little to provide a sensitive measure of hydrate content in water-saturated systems. Thermal diffusivity of methane hydrate is more than twice that of water, however, and its specific heat is about half that of water. Thus, when drilling into or through hydrate-rich sediment, heat from the borehole can raise the formation temperature more than 20 per cent faster than if the formation's pore space contains only water. Thermal properties of methane hydrate should be considered in safety and economic assessments of hydrate-bearing sediment.
-
ArticleImpact of pore fluid chemistry on fine‐grained sediment fabric and compressibility(John Wiley & Sons, 2018-07-17) Jang, Junbong ; Cao, Shuang C. ; Stern, Laura A. ; Kang, Jungwon ; Waite, William F.Fines, defined here as grains or particles, less than 75 μm in diameter, exist nearly ubiquitously in natural sediment, even those classified as coarse. Macroscopic sediment properties, such as compressibility, which relates applied effective stress to the resulting sediment deformation, depend on the fabric of fines. Unlike coarse grains, fines have sizes and masses small enough to be more strongly influenced by electrical interparticle forces than by gravity. These electrical forces acting through pore fluids are influenced by pore fluid chemistry changes. Macroscopic property dependence on pore fluid chemistry must be accounted for in sediment studies involving subsurface flow and sediment stability analyses, as well as in engineered flow situations such as groundwater pollutant remediation, hydrocarbon migration, or other energy resource extraction applications. This study demonstrates how the liquid limit‐based electrical sensitivity index can be used to predict sediment compressibility changes due to pore fluid chemistry changes. Laboratory tests of electrical sensitivity, sedimentation, and compressibility illustrate mechanisms linking microscale and macroscale processes for selected pure, end‐member fines. A specific application considered here is methane extraction via depressurization of gas hydrate‐bearing sediment, which causes a dramatic pore water salinity drop concurrent with sediment being compressed by the imposed effective stress increase.
-
ArticleEstimating pore-space gas hydrate saturations from well log acoustic data(American Geophysical Union, 2008-07-09) Lee, Myung W. ; Waite, William F.Relating pore-space gas hydrate saturation to sonic velocity data is important for remotely estimating gas hydrate concentration in sediment. In the present study, sonic velocities of gas hydrate–bearing sands are modeled using a three-phase Biot-type theory in which sand, gas hydrate, and pore fluid form three homogeneous, interwoven frameworks. This theory is developed using well log compressional and shear wave velocity data from the Mallik 5L-38 permafrost gas hydrate research well in Canada and applied to well log data from hydrate-bearing sands in the Alaskan permafrost, Gulf of Mexico, and northern Cascadia margin. Velocity-based gas hydrate saturation estimates are in good agreement with Nuclear Magneto Resonance and resistivity log estimates over the complete range of observed gas hydrate saturations.