* Sea-Bird SBE 9 Data File:
* FileName = D:\CTD Data\2022\PE22_03_Thrash\C6C_2.hdr
* Software Version Seasave V 7.26.7.107
* Temperature SN = 6316
* Conductivity SN = 4761
* Number of Bytes Per Scan = 40
* Number of Voltage Words = 5
* Number of Scans Averaged by the Deck Unit = 24
* System UpLoad Time = Aug 03 2021 15:32:26
* NMEA Latitude = 28 52.10 N
* NMEA Longitude = 090 29.36 W
* NMEA UTC (Time) = Aug 03 2021  15:32:23
* Store Lat/Lon Data = Append to Every Scan
* SBE 11plus V 5.2
* number of scans to average = 24
* pressure baud rate = 9600
* NMEA baud rate = 9600
* surface PAR voltage added to scan
* A/D offset = 2
* Latitude/Longitude added to scan
* GPIB address = 1
* advance primary conductivity  0.073 seconds
* advance secondary conductivity  0.073 seconds
* autorun on power up is disabled
* S>
* System UTC = Aug 03 2021 15:32:26
# nquan = 16
# nvalues = 212                                   
# units = specified
# name 0 = latitude: Latitude [deg]
# name 1 = longitude: Longitude [deg]
# name 2 = depSM: Depth [salt water, m]
# name 3 = t090C: Temperature [ITS-90, deg C]
# name 4 = t190C: Temperature, 2 [ITS-90, deg C]
# name 5 = c0mS/cm: Conductivity [mS/cm]
# name 6 = c1mS/cm: Conductivity, 2 [mS/cm]
# name 7 = sal00: Salinity, Practical [PSU]
# name 8 = sal11: Salinity, Practical, 2 [PSU]
# name 9 = sbeox0Mg/L: Oxygen, SBE 43 [mg/l]
# name 10 = sbeox1Mg/L: Oxygen, SBE 43, 2 [mg/l]
# name 11 = flC: Fluorescence, Chelsea Aqua 3 Chl Con [ug/l]
# name 12 = ph: pH
# name 13 = orp: Oxidation Reduction Potential [mV]
# name 14 = wetCDOM: Fluorescence, WET Labs CDOM [mg/m^3]
# name 15 = flag:  0.000e+00
# span 0 =   28.86780,   28.86844                 
# span 1 =  -90.48930,  -90.48720                 
# span 2 =      1.880,     19.091                 
# span 3 =    29.3322,    30.6621                 
# span 4 =    29.3326,    30.6634                 
# span 5 =  42.185865,  58.131659                 
# span 6 =  42.194925,  58.139689                 
# span 7 =    24.2998,    35.1643                 
# span 8 =    24.3056,    35.1705                 
# span 9 =     5.0180,     6.2593                 
# span 10 =     4.8956,     6.1047                
# span 11 =     0.9334,     7.2242                
# span 12 =      8.381,      8.609                
# span 13 =  -483.2402,  -453.6128                
# span 14 =    -0.2639,     2.9229                
# span 15 = 0.0000e+00, 0.0000e+00                
# interval = seconds: 1
# start_time = Aug 03 2021 15:32:23 [NMEA time, header]
# bad_flag = -9.990e-29
# <Sensors count="15" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>6316</SerialNumber>
#       <CalibrationDate>10-22-20</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.39947286e-003</G>
#       <H>6.38309239e-004</H>
#       <I>2.27144797e-005</I>
#       <J>2.16709081e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>4761</SerialNumber>
#       <CalibrationDate>10-13-20</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-9.78305784e+000</G>
#         <H>1.26201815e+000</H>
#         <I>-2.35677945e-004</I>
#         <J>7.90281932e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>1357</SerialNumber>
#       <CalibrationDate>10-14-20</CalibrationDate>
#       <C1>-4.631309e+004</C1>
#       <C2>7.306489e-001</C2>
#       <C3>1.502500e-002</C3>
#       <D1>3.645300e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>3.009465e+001</T1>
#       <T2>-2.793230e-005</T2>
#       <T3>3.407780e-006</T3>
#       <T4>4.862040e-009</T4>
#       <Slope>0.99994000</Slope>
#       <Offset>-0.56790</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.280910e-002</AD590M>
#       <AD590B>-8.969920e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>6321</SerialNumber>
#       <CalibrationDate>10-28-2020</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.36728153e-003</G>
#       <H>6.37888420e-004</H>
#       <I>2.24228021e-005</I>
#       <J>2.11848538e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>4764</SerialNumber>
#       <CalibrationDate>10-13-2020</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-9.76706617e+000</G>
#         <H>1.27736245e+000</H>
#         <I>7.91350585e-005</I>
#         <J>5.77902406e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0803</SerialNumber>
#       <CalibrationDate>11-03-20</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>4.9277e-001</Soc>
#         <offset>-0.5239</offset>
#         <A>-5.3481e-003</A>
#         <B> 2.3875e-004</B>
#         <C>-3.4588e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.4300</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Oxygen, SBE 43, 2 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0810</SerialNumber>
#       <CalibrationDate>10-15-20</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>4.2961e-001</Soc>
#         <offset>-0.5138</offset>
#         <A>-5.9396e-003</A>
#         <B> 2.6543e-004</B>
#         <C>-3.8360e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.5200</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, Transmissometer, WET Labs C-Star -->
#     <WET_LabsCStar SensorID="71" >
#       <SerialNumber>CST-1848DP</SerialNumber>
#       <CalibrationDate>1-29-2020</CalibrationDate>
#       <M>20.9104</M>
#       <B>-0.0715</B>
#       <PathLength>0.250</PathLength>
#     </WET_LabsCStar>
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>0937</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ScaleFactor>14.190</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, Fluorometer, WET Labs ECO CDOM -->
#     <FluoroWetlabCDOM_Sensor SensorID="19" >
#       <SerialNumber>1374</SerialNumber>
#       <CalibrationDate>2/10/20</CalibrationDate>
#       <ScaleFactor>87.000</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.036</Vblank>
#     </FluoroWetlabCDOM_Sensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, Fluorometer, Chelsea Aqua 3 -->
#     <FluoroChelseaAqua3Sensor SensorID="5" >
#       <SerialNumber>088-139</SerialNumber>
#       <CalibrationDate>18-06-2019</CalibrationDate>
#       <VB>0.138470</VB>
#       <V1>1.395780</V1>
#       <Vacetone>0.180950</Vacetone>
#       <ScaleFactor>1.000000</ScaleFactor>
#       <Slope>1.000000</Slope>
#       <Offset>0.000000</Offset>
#     </FluoroChelseaAqua3Sensor>
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, pH -->
#     <pH_Sensor SensorID="43" >
#       <SerialNumber>0276</SerialNumber>
#       <CalibrationDate>May-8-2019</CalibrationDate>
#       <Slope>4.5577</Slope>
#       <Offset>2.6137</Offset>
#     </pH_Sensor>
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, Oxidation Reduction Potential -->
#     <OxidationReductionPotentialSensor SensorID="41" >
#       <SerialNumber>0276</SerialNumber>
#       <CalibrationDate>May-8-2019</CalibrationDate>
#       <B>2.497900</B>
#       <M>-0.495200</M>
#       <Offset>0.0</Offset>
#     </OxidationReductionPotentialSensor>
#   </sensor>
#   <sensor Channel="14" >
#     <!-- SPAR voltage, Unavailable -->
#   </sensor>
#   <sensor Channel="15" >
#     <!-- SPAR voltage, SPAR, Biospherical/Licor -->
#     <SPAR_Sensor SensorID="51" >
#       <SerialNumber></SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ConversionUnits>1</ConversionUnits>
#       <ConversionFactor>1.0000e+000</ConversionFactor>
#       <RatioMultiplier>0.00000000</RatioMultiplier>
#     </SPAR_Sensor>
#   </sensor>
# </Sensors>
# datcnv_date = Aug 08 2021 12:33:46, 7.26.7.114 [datcnv_vars = 15]
# datcnv_in = D:\CTD Data\2022\PE22_03_Thrash\C6C_2.hex D:\CTD Data\2022\PE22_03_Thrash\PE22_03_Thrash.xmlcon
# datcnv_skipover = 0
# datcnv_ox_hysteresis_correction = yes
# datcnv_ox_tau_correction = yes
# file_type = ascii